> For the complete documentation index, see [llms.txt](https://luum.io/llms.txt).
> Canonical page: [X-PoE Integrated LED Driver Specification](https://luum.io/docs/install-guides/xpoe-integrated-led-driver-specification).

LUUM.IO

# **X-PoE Integrated LED Driver Specification** - GUIDE

## Overview

The Luum X-PoE lighting controller includes an integrated dual-channel LED driver on every port, purpose-built for low-voltage digital lighting systems. This document defines the electrical characteristics, integration guidelines, and compatibility requirements for fixture manufacturers intending to use the X-PoE port as the primary LED driver.

Each port on the X-PoE lighting controller behaves like a 2-channel Class 2 constant current driver, capable of powering and dimming modern LED modules directly, without the need for a separate local driver.

## Driver Summary (Per Port)

| PARAMETER | VALUE/RANGE | NOTES |
| --- | --- | --- |
| **Max Output Current**<br>**(Per Channel)** | 1115mA | Hardware limited to Class 2 per channel |
| **Output Voltage** | 24-54VDC | Fixture must operate within this range |
| **Number Of Channels** | 2 | Independently controllable (CH1, CH2) |
| **Total Power**<br>**(Per Port)** | Up to 130W (typical) | Port-level power budget across 2 channels |
| **Dimming Type** | Digital (0-100%, 12-bit resolution) | Dimming control via Luum system |
| **Isolation** | Class 2 | Limited energy, inherently safe |

## Integration Guidelines

**Voltage Compatibility**

- Fixtures **must operate above 24V** (Vf >23V).
- Fixtures that operate closer to **48V will draw less current** and better utilize port power (due to lower cable losses and switching overhead).
- Voltage must not exceed **54V** at any point in the load.

**Current And Power Rules**

- Each channel delivers a **maximum of 1115mA**.
- In most cases, fixtures will be energized with 200mA of current to “glow”, then configured via software to the correct current output.
- **Power = Forward Voltage × Field Programmed Current** (max of 1.115 A per channel).

**Channel Usage**

- Two channels are available per port:
    - **Single-channel fixtures** can use CH1 or CH2.
    - **Dual-channel fixtures** (e.g. tunable white, up/downlight) should map each LED circuit to its own channel.
- Channels are software addressable and controlled independently in the Luum commissioning software.

> **Combining (Aggregating) Channels**
> - Single-channel fixtures that require between 1115-2230mA can utilize a purpose built XPD that combines both X-PoE channels on a port to power the fixture. This XPD must come installed on the fixture and the wiring must be internal to the fixture.
> - Contact [Luum.io](mailto:sales@luum.io) to discuss options for any fixtures that require greater than 2230mA.
>
**Fixture Wiring**

- Fixtures should be terminated with clearly labeled **+ / − wires** per channel.
- Shared neutral or other creative wiring schemes are not recommended unless validated with Luum.
- Label channel usage in fixture documentation (e.g. “CH1 = Downlight, CH2 = Uplight”).

**Fixture Design Considerations**

- Prefer **constant current** modules over constant voltage designs.
- LED strings should be designed for forward voltages within the optimal operating range (36–48 V recommended), with voltages closer to 48 V being ideal to most efficiently optimize the use of each channel.
- If a fixture already includes a remote constant current driver, replacing it with the X-PoE integrated driver is typically straightforward. Fixture manufacturers should confirm compatibility and remove any redundant driver electronics before integration.
- Avoid adding local drivers, regulators, or converters unless absolutely necessary.

## Fixture Certification

To be listed as **X-PoE Compatible**, fixtures must:

1. Operate reliably with 1115mA constant current input.
2. Maintain forward voltage between 24–54V across all temperatures.
3. Be tested and approved by Luum's hardware integration team.

## Example Fixture Loads

| FIXTURE TYPE | FORWARD VOLTAGE | POWER (W) | NOTES |
| --- | --- | --- | --- |
| Linear Static White | 40V | 46W | Typical for direct-lit linear |
| Tunable White | 36V x 2 | 83W | One channel per CCT circuit |
| High-Power Pendant | 48V | 110W | Efficient full-port usage |
| Low-Power Accent | 28V | 32W | May leave power headroom |

## Notes For Fixture Engineers

- Treat the port like a **DC output with current source behavior**, not a voltage source.
- If integrating test jacks or EMC filters, verify they are safe for a 1115 mA CC circuit.
- The system does not support analog dimming or local potentiometer control — **all control is via Luum’s networked system or 3rd party integration**.

## Overdriving Vs. Underdriving

LEDs are tolerant of being slightly underdriven without performance issues. For instance, a fixture rated at 70 W might perform acceptably at 65 W if the photometric performance remains within spec. Fixture manufacturers are encouraged to verify the delivered output at the expected current and confirm lumen delivery with photometric testing rather than relying solely on nominal wattage.

## Related Information

### Technical Support

Questions about this specification can be sent to [support@luum.io](mailto:support@luum.io). Fixture options above 2230 mA can be sent to [sales@luum.io](mailto:sales@luum.io).

### Document Feedback

While we have taken great care to ensure the accuracy and completeness of this document, we welcome your feedback and suggestions. If you notice any errors or omissions, or feel a topic could benefit from further explanation, please email your feedback to [support@luum.io](mailto:support@luum.io).

### Revision History

| Date | Revision | Notes |
| --- | --- | --- |
| 11/3/2026 | A | Converted to the current guide format. |

### Disclaimer

All rights, title, and interest in and to this guide, including without limitation all copyright, trademark, patent, trade secret, and other proprietary rights, belong solely and exclusively to Luum.io and/or its licensors. This guide is provided solely for the purpose of specifying a fixture that uses the X-PoE port as its LED driver, and no license or other rights are granted or implied hereby. No part of this guide may be reproduced, distributed, or transmitted in any form or by any means, including photocopying, recording, or other electronic or mechanical methods, without the prior written permission of Luum.io. The contents of this guide are subject to change without notice. The information contained herein is provided on an 'as is' basis and is for informational purposes only. Luum.io makes no warranty, express or implied, as to the accuracy, completeness, or usefulness of this information, nor does it assume any legal liability or responsibility for the consequences of any errors or omissions therein. The names of actual companies and products mentioned herein may be the trademarks of their respective owners.

---

_©2026 Luum.io. All rights reserved._
